Phoenix - Your AI AssistantEagle Pcb Projects
Looking for freelance Eagle Pcb jobs and project work? PeoplePerHour has you covered.
opportunity
PCB designer for CM4 carrier with isolated RS422/RS485
We need an experienced electronics/PCB designer to design a custom Raspberry Pi Compute Module 4 carrier board for an industrial field test tool. The board will be used for roadside electronic sign testing and needs robust isolated serial communications, Ethernet, WiFi support via the CM4 module, touchscreen display support and a connector for an address plug socket. We are developing a portable field tester for roadside electronic signs and controllers. The unit will run Linux on a Raspberry Pi CM4 and needs to communicate with equipment over isolated RS422/RS485 and Ethernet. It needs to be designed sensibly for field use, with proper isolation, protection, clear connectors and future small-batch manufacture in mind. Required board features: • Raspberry Pi Compute Module 4 socket. • Support for CM4 wireless variant for WiFi/Bluetooth. • Gigabit Ethernet port using the CM4 native Ethernet interface. • Two independent isolated serial ports. • Each serial port to support full-duplex 4-wire RS422: TX+, TX-, RX+, RX-. • Ideally allow RS485 configuration as well, if practical: 2-wire half-duplex RS485 or 4-wire RS485/RS422 mode. • Digital isolation on the serial ports. • Isolated DC/DC supply for the field side of the serial interfaces. • TVS/ESD protection on field connections. • Termination and bias options per port, preferably via jumpers or DIP switches. • TX/RX activity LEDs per port. • Connector for an external address plug socket. • MIPI DSI touchscreen display connector, similar to the Waveshare CM4 Nano B: 15-pin 1.0mm FPC connector, suitable for common Raspberry Pi DSI touchscreens such as 4.3 inch, 5 inch or 7 inch. • Allow for touchscreen/control lines where required. • Mechanical clearance and routing allowance for the screen ribbon cable. • WiFi/Bluetooth to be provided by the CM4 wireless module, not a separate WiFi chipset. • RF/mechanical allowance for CM4 onboard antenna or external antenna connection. • Protected power input suitable for field equipment. • Status LEDs for power, CM4 activity, Ethernet, serial activity and isolated power good. • Sensible mounting holes and enclosure-friendly layout. Preferred technical direction: The serial ports should probably be implemented using a dual UART interface from the CM4, for example an SPI-to-dual-UART device such as the SC16IS752/SC16IS762 family or equivalent, feeding isolated RS422/RS485 transceivers. We are open to the designer recommending exact parts, but the design must be supportable and manufacturable, not based on obscure parts with poor availability. Deliverables required: • Schematic design. • PCB layout. • Gerber files. • Pick-and-place / assembly outputs. • Bill of materials with manufacturer part numbers. • Any required configuration notes for CM4 interfaces used, especially DSI, SPI/UART and Ethernet. • Basic bring-up notes and test points. Useful reference board: The Waveshare CM4 Nano B is a useful reference for the compact CM4 carrier concept, particularly the CM4 socket, Ethernet, DSI touchscreen connector and general small carrier-board approach. Our board needs to add robust isolated dual RS422/RS485 and address plug support. Please only respond if you have experience designing Raspberry Pi CM4 carrier boards, isolated serial interfaces, or industrial communications hardware. We are happy to work iteratively, but need someone who can make sensible engineering decisions and produce files suitable for manufacture. We can provide more detail on the address plug wiring and preferred connectors once we have selected a designer.
Accessories and 3D PRINTING
Seeking an experienced accessories and 3D printing specialist to manufacture and assemble a smart mobile phone/tablet carrier. Project details will be disclosed progressively upon NDA execution. Strong English communication is essential; identity verification such as passport or driving licence may be required. Comprehensive operating procedures, manufacturing documentation, and transcripts will be supplied. Testing of the finished product is required. PCB production is currently available for eventual integration. Reliable, detail-oriented professionals encouraged to bid just the carrier needed ATM and material required will be advised on winning bid.
opportunity
SEO to Promote Corporate Training Website (organic visibility)
Project: Digital Marketing & SEO to Promote Corporate Training Website (Spanish & English) ### About us We are Eagles Flight México, a corporate training and experiential learning company. Our websites are: - [https://www.eaglesflight.mx](https://www.eaglesflight.mx) - https://www.eaglesflight.com.mx We design and deliver workshops, simulations and training programs for companies (leadership, teamwork, culture, customer service, safety, etc.). Our goal is to increase qualified leads from HR, Training & Development and business leaders in Mexico and Latin America. *** ### Objective of this project I want to hire a freelancer to increase our online visibility and generate more inquiries from companies searching for: - “talleres”, “capacitaciones”, “workshops”, “simulaciones” - corporate training, team building, leadership workshops - in Spanish and English, mainly in Mexico. The focus is on improving our presence in search results and relevant platforms, not on generic followers. *** ### Scope of work (what I need) Please propose a strategy and execution plan that can include most of the following: - **SEO audit and on‑page optimization** - Review both domains (.mx and .com.mx) and suggest structure and technical improvements (speed, metadata, headings, internal links, etc.). - Keyword research in Spanish and English focused on corporate training / workshops in Mexico. - Optimize key pages (homepage, services, workshops, contact) with agreed keywords. - **Content and positioning** - Propose and create SEO‑friendly content (blog posts, landing pages or FAQs) targeting our ideal customer (HR, training managers, business leaders). - Suggestions for new landing pages for specific topics (leadership workshop, team‑building workshop, safety culture, etc.). - **Local and business presence** - Review and improve our visibility in Google (Google Business Profile) and other relevant business listings/directories, if useful for B2B. - **Performance and tracking** - Set up or review analytics and conversions (contact forms, quote requests, calls, downloads). - Provide a simple monthly report: traffic, rankings for main keywords, and leads (inquiries) generated. I am especially interested in freelancers who can explain what actions will generate **more qualified leads**, not just traffic. *** ### Requirements for the freelancer - Experience with SEO and digital marketing for B2B services (ideally training, consulting or similar professional services). - Fluent Spanish, and at least good written English. - Ability to work with WordPress (or advise our developer with clear instructions). - Able to communicate clearly and provide simple reports. Please include in your proposal: 1. A short description of your experience with similar projects. 2. 2–3 examples or links of B2B sites you have helped grow (if possible). 3. What you would do in the **first 30 days** of this project. 4. Your suggested **monthly fee** and how many hours/activities it includes. *** ### Project type and duration - Type: Ongoing project (we can start with a 1–3 month test). - Approximate budget: Please propose a realistic monthly budget for SEO + content + optimization. - Start date: As soon as we select the right freelancer. ***
opportunity
Digital Marketing & SEO to Promote Corporate Training Website
About us We are Eagles Flight México, a corporate training and experiential learning company. Our websites are: - [https://www.eaglesflight.mx](https://www.eaglesflight.mx) - https://www.eaglesflight.com.mx We design and deliver workshops, simulations and training programs for companies (leadership, teamwork, culture, customer service, safety, etc.). Our goal is to increase qualified leads from HR, Training & Development and business leaders in Mexico and Latin America. *** ### Objective of this project I want to hire a freelancer to increase our online visibility and generate more inquiries from companies searching for: - “talleres”, “capacitaciones”, “workshops”, “simulaciones” - corporate training, team building, leadership workshops - in Spanish and English, mainly in Mexico. The focus is on improving our presence in search results and relevant platforms, not on generic followers. *** ### Scope of work (what I need) Please propose a strategy and execution plan that can include most of the following: - **SEO audit and on‑page optimization** - Review both domains (.mx and .com.mx) and suggest structure and technical improvements (speed, metadata, headings, internal links, etc.). - Keyword research in Spanish and English focused on corporate training / workshops in Mexico. - Optimize key pages (homepage, services, workshops, contact) with agreed keywords. - **Content and positioning** - Propose and create SEO‑friendly content (blog posts, landing pages or FAQs) targeting our ideal customer (HR, training managers, business leaders). - Suggestions for new landing pages for specific topics (leadership workshop, team‑building workshop, safety culture, etc.). - **Local and business presence** - Review and improve our visibility in Google (Google Business Profile) and other relevant business listings/directories, if useful for B2B. - **Performance and tracking** - Set up or review analytics and conversions (contact forms, quote requests, calls, downloads). - Provide a simple monthly report: traffic, rankings for main keywords, and leads (inquiries) generated. I am especially interested in freelancers who can explain what actions will generate **more qualified leads**, not just traffic. *** ### Requirements for the freelancer - Experience with SEO and digital marketing for B2B services (ideally training, consulting or similar professional services). - Fluent Spanish, and at least good written English. - Ability to work with WordPress (or advise our developer with clear instructions). - Able to communicate clearly and provide simple reports. Please include in your proposal: 1. A short description of your experience with similar projects. 2. 2–3 examples or links of B2B sites you have helped grow (if possible). 3. What you would do in the **first 30 days** of this project. 4. Your suggested **monthly fee** and how many hours/activities it includes. *** ### Project type and duration - Type: Ongoing project (we can start with a 1–3 month test). - Approximate budget: Please propose a realistic monthly budget for SEO + content + optimization. - Start date: As soon as we select the right freelancer.
opportunity
"Senior Amazon Brand Store Operator
A Screaming Eagle LLC is a heritage publishing brand launching on Amazon in July 2026. We hold the registered BAND OF BROTHERS™ trademarks in Class 16 and Class 25 (USPTO serials 99744587 and 99744589). The launch is anchored to the 25th Anniversary Symposium at the National WWII Museum, New Orleans, July 31–August 1, 2026. The business is built around the documented WWII combat artwork and memoir of T/Sgt. Burton P. "Pat" Christenson, Easy Company, 506th PIR, 101st Airborne — the unit Stephen Ambrose immortalized in Band of Brothers. The book opens with Major Dick Winters' personal letter confirming Pat as second man out the door behind Winters on the Normandy jump. The drawings were exhibited at the 2001 Hollywood Bowl HBO premiere and are independently valued in the millions. Stephen Ambrose called them "priceless." This is not a typical Amazon catalog launch. It is a bestseller-quality book launch with a coordinated 230-design premium catalog rollout, backed by registered trademarks and a 400+ million-viewer audience for the source material. First-year business projection: $1M to $6M gross revenue depending on execution. LOCKED LAUNCH DATES — NON-NEGOTIABLE CONTRACT TERMS — July 1, 2026: Marketing infrastructure live. Brand Registry submitted, book listing optimized, A+ Content deployed, Author Central built, Amazon PPC running. — July 15, 2026: Book live on Amazon. — August 15, 2026: Full catalog live. 230 designs — 86 Heritage Line apparel and 100 Classic Line apparel via Printful, plus 44 Heritage Prints via Prodigi. Full parent-child variation architecture, ~10,000–21,000 SKUs. — August 30, 2026: 6-page Brand Store live. Tiered A+ Content (30 Premium custom, 60 Standard, 140 Basic shell). — August 30–September 29: Intensive PPC management across full catalog. COMPENSATION We are open to proposals from senior operators across a range of engagement values. Quote what you genuinely need to deliver exceptional work on the locked timeline. Our engagement structure is fixed-price milestones tied to deliverables. We do not work with open-ended retainers or hourly billing during launch. Plus an ongoing monthly retainer beginning October for PPC optimization and catalog health. Underbidding to win the contract and then reducing scope is not acceptable. WHO WE WANT A senior Amazon Brand Store operator or specialty publishing agency that: — Has personally built multi-page Brand Stores at scale — Has launched books on Amazon at bestseller-quality positioning — Has handled parent-child variation architecture at 5,000+ SKU scale — Has worked with Printful and Prodigi POD integration — Can commit full-time for the four-month launch window — Delivers daily written updates — Treats the engagement as a craft, not a task list WHO WE DO NOT WANT — Generic operators who treat the book as another listing — Open-ended retainer or hourly billing during launch — Junior operators learning at our scale — Agency wrappers that hand work to unnamed team members — Operators who require a call before delivering written diagnostics — Anyone who cannot commit to the three locked dates PROPOSALS MUST ADDRESS ALL FIVE ITEMS IN WRITING Brand Store credentials: 2–3 live URLs you personally built, with specific scope per URL (lead operator vs. supported as part of a team) Book launch experience: specific books launched on Amazon, with results if available Variation architecture: largest SKU count you have personally deployed with parent-child architecture, category, and live URL if possible Book positioning: how would you frame the editorial pedigree (developmental editor Dr. Katherine Wilson, PhD; Winters' opening letter; the drawings' 2001 Hollywood Bowl provenance with Stephen Ambrose's "priceless" endorsement; BAND OF BROTHERS™ trademark protection) in the Amazon listing copy, A+ Content, and Brand Store narrative? Be specific. Your fixed-price quote broken into milestones tied to the deliverables above, plus proposed monthly retainer beginning October. Proposals without all five items will not be considered. Templated proposals with generic Amazon marketing language will be declined immediately.
Past "Eagle-pcb" Projects
KiCad PCB Designer for Custom Electronics Project
We are seeking an experienced PCB designer with strong proficiency in KiCad to assist with the design and development of a custom printed circuit board. The ideal candidate will have a solid background in electronics design, schematic capture, and PCB layout, with attention to detail and a focus on manufacturability.
opportunity
PCB Modification
Hello, I am needing someone to modify an existing PCB for a stepper motor which controls a motion on a display unit. We had a PCB designed to control a stepper motor a few years ago, but we have made a few changes in the mean time and we would like a new PCB that reflects these changes. 1) We are using a new stepper motor which has a different pin out on it. To use our existing PCB we are swapping 2 of the wires in the one cable plug that connects to the stepper motor. We would need this change made to the PCB if possible so that we can use a standard cable without modification. 2) There are little solder pads that are connected with solder bridge to select the number of steps for the stepper motor. We have long since decided what the correct selection is and this could be connected in the PCB without needing to solder it to select the number of steps. 3) We will need to have a prototype made, which we can organise to test whatever modifications are made. We have full schematics available for modification.
opportunity
Source leads and obtain bookings for an online training course
Project overview: We need someone to source qualified leads and secure at least 10 paid bookings for our 2-day Power BI Masterclass. The first cohort runs on 22nd June 2026. The course is delivered online, so leads can be based anywhere, though UK-based prospects are preferred and must be English speaking. If the first month succeeds, there is ongoing monthly work available as we run this course once per month. Measurable success will be heavily rewarded: this means if you get secured bookings within the next 5 days, if you exceed 10 bookings, or any other comparable success metrics, you will receive a bonus payment and secured ongoing monthly work. Course details: The masterclass is a 2-day, expert-led online course priced at £600 inc VAT per person. It covers Power BI from fundamentals to advanced DAX, dashboard building, and deployment, across 7 modules. No prior Power BI experience is required from attendees. Full course information, modules, and testimonials are at https://redeagle.tech/training/power-bi-masterclass. Target audience: Ideal leads include business analysts, data analysts, reporting professionals, finance managers, FP&A professionals, finance directors, and operations managers or directors at SMEs. Anyone whose role involves regular reporting from Excel, SQL, or cloud data sources is a fit. We can also accommodate students. Company size: UK SMEs and mid-market are the sweet spot. We have FTSE 100 training experience but corporate L&D cycles are too slow for this timeline, so focus on individuals with budget authority or small teams of 2 to 5. Geography: UK preferred but the course is online and open to international attendees. Remuneration: We pay a £150 starter fee when we accept your proposal on PeoplePerHour, plus £150 per confirmed paid booking. For 10 bookings on the 22nd June cohort, total earnings would be £1,650. Partial success is paid pro rata: every confirmed booking earns the £150 fee regardless of whether the full 10 is hit. Per-booking payments are released through PeoplePerHour weekly in arrears, once the customer's payment clears via our Shopify checkout. If a booking is refunded or cancelled before the course runs, the corresponding £150 is deducted from the next payment. This allows us to ensure you are paid sooner than 22nd June. How we track your bookings: You will be issued a unique discount code worth [£50] off the standard £600 price. This serves two purposes: it gives you a tangible incentive to offer prospects, and it lets us track every booking attributed to your outreach. The code is yours alone for the duration of the engagement and does not stack with any other promotion. Timeline and targets: The first cohort begins on 22nd June 2026. All 10 places must be booked by 17th June at the latest, and earlier is strongly preferred so we can confirm logistics. We expect to see initial bookings within 3 weeks of starting. If no bookings have come through by week 3, we will review the approach together before deciding whether to continue. Reporting: We expect regular communication throughout covering outreach volume, response rates, replies in progress, and any obstacles. This is helps us spot when outreach copy needs tweaking before momentum is lost. How you work -Source the leads: source a list of appropriate leads matching the audience described above. If using LinkedIn, you must provide the profile you will be contacting from before outreach begins. If using email, you must use a warmed-up sending domain with healthy deliverability, or a reputable cold-email platform such as SalesHandy, Instantly, or Lemlist. Outreach copy must be approved by us before any messages are sent. -Direct prospects to book through our standard Shopify checkout using your discount code. Bookings are tracked automatically through the code. Brand and voice You will be representing Red Eagle Tech, an authorised Microsoft Partner. Outreach must be professional, accurate about what the course covers, and written in a natural human voice with no obvious AI markers. British English throughout. We will share editorial guidelines and assets you can use. Candidate requirements Professional written and spoken English. UK-based preferred. Verifiable LinkedIn profile required. You must show demonstrable lead generation or sales experience with measurable results, whether that is specific campaigns, conversion rates, or client references. Familiarity with B2B outreach to UK SMEs is a strong advantage. What to include in your proposal Please include the LinkedIn profile or sending domain you would use, a summary of your proposed approach, two or three examples of past lead gen or sales work with results, and confirmation of your location. *Proposals that are clearly purely AI-generated with no evidence of authentic experience with profiles with no evidence of prior work in this field will not be considered.* *Lead-gen lists that are generated purely using AI will not be accepted*
opportunity
Printed Circuit board modification
Hello, I have an existing PCB that needs a small modification to adapt to a new stepper motor.
Military Heritage Brand — Full Ecommerce Launch — July 4th
I am the founder of A Screaming Eagle LLC, a veteran owned premium military heritage apparel brand based in San Diego, California. I am the son of T/Sgt. Burton Paul "Pat" Christenson of Easy Company, 506th PIR, 101st Airborne Division — the Band of Brothers. My father was Dick Winters' number two man on the D-Day jump into Normandy and the only combat artist in Easy Company. His fifty original combat drawings appeared in Stephen Ambrose's Band of Brothers book. This is an authenticated American story unlike anything else in the military heritage space. I am launching a complete premium ecommerce brand on July 4th 2026 — the 250th anniversary of America. Hard deadline. Non negotiable. SCOPE OF WORK Shopify store — Complete build with Printful integration, all collections, navigation and checkout tested and working. WordPress website — Separate brand website telling Pat's story. Home, about, press, blog and contact pages. SEO optimized. Amazon — Seller Central verified, Brand Registry submitted, KDP book listings in three formats, A plus Content and Brand Store built. Etsy — Fully built and optimized with all products listed. Fine Art America — Complete gallery with all fifty authenticated combat drawings uploaded with captions. Social media — Facebook, Instagram, TikTok, YouTube and Pinterest fully branded and active with daily content. Product uploads — 400 plus designs across five colorways and four product types. Approximately 4,500 SKUs uploaded across all platforms with fully optimized titles, descriptions and keywords. Email marketing — Welcome, launch, post purchase and abandoned cart sequences built and tested. Advertising — Amazon PPC, Meta and Google campaigns built and ready to deploy July 4th. PR — Press release written and distributed to veteran and military heritage publications domestically and internationally. Full QA and testing complete by July 1st. TIMELINE May 15th — Book soft launch on Amazon KDP. June 6th — D-Day. Full book marketing push. Clothing line teased publicly. July 1st — All stores live and fully tested. July 4th — Full ecommerce launch. WHAT I REQUIRE A complete professional team. Not an individual freelancer. Project manager, Shopify developer, WordPress developer, Amazon specialist, social media manager and advertising specialist working together. Fixed price only. No hourly billing. Milestone payments tied to verified deliverables confirmed on screen share. Daily communication. Weekly progress reports. Shared project management board accessible to me at all times. Live store examples with verifiable results required. Must start this week. Today is April 15th. July 4th is 80 days away. PRICING Please provide your complete fixed price for full setup through June 30th and your proposed monthly retainer starting July 1st. Itemize by platform and deliverable. No hourly rates will be considered. I have had an unsuccessful experience with an agency that overpromised and underdelivered. I need a team that executes every single day without being chased. This brand launches on the 250th birthday of America with a complete premium product line, a published book and a story that connects D-Day 1944 directly to Independence Day 2026. The right team will be part of something extraordinary. Serious professional teams only. Include team structure, live store examples, week by week timeline and complete fixed price with your proposal.
Design and deliver Gerber file for PCB "adapter"
I am looking for an adapter PCB that will allow me to fit a V23086C1001A403 TYCO relay into the 7-pin circuit board of a classic car car control unit. I can provide photos and dimensions of the Mercedes circuit board, as well as pin function. I want to receive a Gerber file for an adapter that I can upload directly into PCBWAY and have manufactured. The adapter will allow me to use the TYCO relay in place of the now obsolete Mercedes relay.
urgent
Hub Dynamic PD
We are developing a premium smart power hub (USB-C PD, multi-port, real-time power monitoring) and are looking for an embedded firmware engineer to lead the MCU firmware layer. The electronic hardware and PCB are already designed. This role focuses on firmware architecture, implementation, and testing. This is not a beginner role. We are looking for someone comfortable working close to hardware and making pragmatic engineering decisions. Responsibilities: - Develop MCU firmware for USB-C PD power management - Implement real-time power monitoring and reporting - Interface with PD controllers, current sensors, and displays (OLED/LCD) - Define safe fallback states and edge-case handling - Collaborate with existing hardware engineer - Prepare firmware for EVT/DVT prototypes Requirements: - Strong experience in embedded C / C++ - MCU firmware (STM32, ESP32, or similar) - USB-C Power Delivery concepts - I2C / SPI / UART - Debugging on real hardware Nice to have: - Power electronics familiarity - Display/UI firmware - EVT → DVT → PVT experience - Consumer electronics background Engagement: - Contract, milestone-based - Remote - Compensation open and based on scope and experience
ESP32 Embedded Firmware – Smooth Sparkler LED Animation
I am developing a wearable LED headband with a continuous, sparkler-style moving light effect. The mechanical design (SolidWorks / STEP) is fully completed and locked. This project is strictly focused on electronics and embedded firmware — no mechanical design, web, or mobile work. The goal is to implement a high-quality LED animation engine on a microcontroller (ESP32 or equivalent) that produces smooth, continuous motion around a 360° addressable LED ring (~72 LEDs). The animation must use fractional (sub-pixel) position tracking and brightness blending across adjacent LEDs — visible LED-to-LED stepping is not acceptable. Scope of Work: • Develop embedded C/C++ firmware for addressable LEDs (WS2812B / SK6812 or equivalent) • Implement continuous 360° motion with one or more moving “sparks” • Use floating-point or fixed-point math to blend brightness between adjacent LEDs • Create smooth trailing glow and subtle flicker (sparkler-style behavior) • Match motion speed and feel to provided reference visuals • Ensure clean, efficient, well-commented firmware suitable for manufacturing Deliverables: • Firmware source code • Short demo video showing slowed-down motion that clearly demonstrates sub-pixel interpolation • Brief explanation of animation logic and LED indexing • Optional: guidance on MCU/LED selection if needed Out of Scope: • Mechanical CAD • PCB layout • Mobile apps or cloud connectivity This project requires experience with embedded systems, microcontroller programming, and addressable LED animation. Please do not apply if your background is primarily web or mobile development.
PIXHAWK V6X CUSTOM PAB CARRIER PCB
I need a PCB design to hold a Pixhawk V6X autopilot cube Breaking out my only needed functions to accept 2.5mm ferruled wires: c1 power c2 power gps 2 can 1 can 2 telem 2. And A1 power gnd and sensor Also require a USB-C and RJ45 on board also. Nice to haves: Can 1 and Can 2 have LED to show correct wiring (green), bad wiring (red) All the pinouts and specifications for the pixhawk autopilot and breakout are freely available online I require from this a finished schematic/design/bom etc that I can send off to get the PCBs manufactured so that I can populate and solder In house
I need a PCB Design for servo controller
I need someone who can design a cheap pcb that can allow me to control a servo via a momentary push button. Pcb (and code) should make it so when the button is depressed the servo actuates and holds for as long as the button is depressed and then returns to normal when not depressed.
pre-funded
Design an double sided Archimedis Spiral PCB
Hello, I need a draftperson who is willing to design for me a double sided PCB with an Archimedis Spiral drawing. Here are the dimensions. Diameter : 90 mm Track width : 1 mm Tracks : 25 Equally spaced. Large Diameter : 90 mm Small Diameter : 25 2 contact holes, 90 and 25 mm dia. Thank You.
Portable microcontroller based I/O expansion board
I have a basic concept for a portable microcontroller based I/O device. I have the schematics and design data what is shown on the pictures in KiCAD format, which I can share with you. The device consist a display, LEDs, rotary encoder, a potentiometer, buttons, some FET based screw terminals, a serial output, a light sensor, a microphone and a speaker, and a BLE UART bridge (JDY-08). This is a 2 PCB sandwich design. It is a 4 layer design right now. I have a mechanical concept, but the schematics contains some serious errors. TODO: - schematics should be checked and errors should be fixed (critical) - the documentation of the JDY-08 says the UART is TTL level, while the rp2350 based microcontroller is 3v3. A level shifter needs to be added (critical) - The MCU should be secured against backpowering via the secondary USB port (would be nice, but I can live without this) The ideal candidate have experience with : - microcontroller based designs - can read and createelectronic schematics This is a unique piece production, no serial production is considered. Therefore I plan to keep the easily available MCU board. I'd like to keep the current PCB mechanical design. I need only schematics changes. I am able to do the PCB modifications.
Eagle CAD - Change DIL 32 pin socket to PLCC 32
I have a simple board layout in Eagle CAD and I need the change the 32 pin socket from DIL to PLCC 32 through hole. It uses a 27c010 and I need the same tracks etc. Thank you for considering my project. Tim
urgent
Custom Pixhawk V6X Carrier board PCB
I need a custom carrier board designed for a pixhawk V6X autopilot It'll be simplified, and instead of the standard JST connectors, I require spring terminals for ferrule crimps for all I/O A Actual RJ45 connector and a USBC connector, power LED And a LED status for CAN1 & 2 that shows correct wiring vs incorrect Ideally with files for eagle / kicad 9 for later modification if needed
I need an expert designer
I need a professional graphic designer with high level attention to detail. I have 2 images that need to be altered. The edit and finish should be exactly and consistent with the original artwork First image 1. The text Eagle fly will be added to plane head 2. Letter G replace the star 3. Word logo that will need to have the same effect as the artwork Second image 1. Replace number 4 with 1 2. Add the word eagle fly to the collar 3. Change some of the badges 4. Word logo that will need to have the same effect as the artwork