I need an electronic circuit Arduino designed and built to control a Stepper motor.
- or -
Post a project like this$$
- Posted:
- Proposals: 7
- Remote
- #1620661
- Expired
Embedded Systems, Programming, Circuit Designing, Automation, Pcb Designing, Technical Research,IoT
Lahore
1525863171147617135751717371172044417265751727725
Description
Experience Level: Intermediate
General information for the business: Animal feeders
Kind of development: New program from scratch
Num. of modules: 1
Description of requirements/functionality: Project design to control a Bi Polar stepper motor using ideally an Arduino.
The Project is for design, code and supply a working prototype here to the Uk.
1. Radio Control turn circuit on ( press 1) LED turns green, possible sounder 2 sec burst confirmation.
2. Radio Control select program 2-6
3. Random delay before Bi polar motor activation. ( between 2-10sec )
4. Random turn stepper motor +90 or -90 ( +90 Clockwise, -90 Anticlockwise )
5. Fixed delay after first activation say 1.5 seconds
6. Return to Zero position ( If step 4 random selection was +90 then return should be -90 & vice versa )
7. Random delay between (2-10 sec)
8. Start loop again back at step No:-4
9. Loop continues until a fixed number of cycles has been completed ( Say 10 Cycles )
10. Stop! Buzzer sounds to confirm cycle completed ( Say 2 seconds burst )
4 programs selectable from the radio control channels 2-6 all to run as above but with a different fixed variant on step 5.
Each program has an LED confirmation. So 6 LED’s in total.
Arduino Platform and buzzer parts.
Something like a Nema 14 Bi Polar stepper motor, and suitable driver.
12v 6 channel RF 433Hz Radio control 100m range or equal.
The project is to design, code, and supply a working prototype unit for testing to the UK.
Payment once agreed say something like 50% on design and the rest on shipping and successful testing here
in the UK.
Best regards
Extra notes:
Kind of development: New program from scratch
Num. of modules: 1
Description of requirements/functionality: Project design to control a Bi Polar stepper motor using ideally an Arduino.
The Project is for design, code and supply a working prototype here to the Uk.
1. Radio Control turn circuit on ( press 1) LED turns green, possible sounder 2 sec burst confirmation.
2. Radio Control select program 2-6
3. Random delay before Bi polar motor activation. ( between 2-10sec )
4. Random turn stepper motor +90 or -90 ( +90 Clockwise, -90 Anticlockwise )
5. Fixed delay after first activation say 1.5 seconds
6. Return to Zero position ( If step 4 random selection was +90 then return should be -90 & vice versa )
7. Random delay between (2-10 sec)
8. Start loop again back at step No:-4
9. Loop continues until a fixed number of cycles has been completed ( Say 10 Cycles )
10. Stop! Buzzer sounds to confirm cycle completed ( Say 2 seconds burst )
4 programs selectable from the radio control channels 2-6 all to run as above but with a different fixed variant on step 5.
Each program has an LED confirmation. So 6 LED’s in total.
Arduino Platform and buzzer parts.
Something like a Nema 14 Bi Polar stepper motor, and suitable driver.
12v 6 channel RF 433Hz Radio control 100m range or equal.
The project is to design, code, and supply a working prototype unit for testing to the UK.
Payment once agreed say something like 50% on design and the rest on shipping and successful testing here
in the UK.
Best regards
Extra notes:
Mr J.
100% (3)Projects Completed
8
Freelancers worked with
6
Projects awarded
22%
Last project
22 Jun 2018
United Kingdom
New Proposal
Login to your account and send a proposal now to get this project.
Log inClarification Board Ask a Question
-
There are no clarification messages.
We collect cookies to enable the proper functioning and security of our website, and to enhance your experience. By clicking on 'Accept All Cookies', you consent to the use of these cookies. You can change your 'Cookies Settings' at any time. For more information, please read ourCookie Policy
Cookie Settings
Accept All Cookies