Do embedded firmware development by using microcontroller
Delivery in
1 day
- Views 32
Amount of days required to complete work for this Offer as set by the freelancer.
Rating of the Offer as calculated from other buyers' reviews.
Average time for the freelancer to first reply on the workstream after purchase or contact on this Offer.
What you get with this Offer
I specialize in C, C++, and Embedded C Programming for various Microcontroller Architectures, including STM32, ESP32, and Arduino.
With over 5 years of experience as an Embedded Software Engineer, I am dedicated to providing top-notch STM32 firmware solutions to ensure the success of your projects. Let's discuss your requirements and make your projects a success.
I have experience in the following areas:
Microcontrollers: STM Cortex m0 m3 m4 m7
Communication Protocols & Drivers: USART/UART, I2C, SPI, CANBUS, I2S
Real Time Operating System (RTOS): FreeRTOS
Data Transmission: MQTT, UDP, TCP
Data Transmission Modules: SIMCOM, QUECTEL, FIBOCOM
Software to be used:
1. ESP32
2. STM32
3. Arduino
4. Raspbery Pi
Languages
1. Embedded C
2. C++
Sensors :
1. Encoder
2. Temperature
3. Humidity
4. Ultrasonic
5. Current
6. Voltage
7. Magnetometer/Gyroscope
8. Accelerometer
9. Barometer
10. Pressure sensor
11. Gas/Smoke
12. Buttons
13. Switches
14. Infra-red (PIR Sensor)
15. Light Dependent Resistor (LDR)
16. Vibration
17. GPS
18. Sound
19. Weight
Displays :
1. GLDC
2. 20x4 LCD
3. 16X2 LCD
4. OLED
5. TFT
Actuators :
1. Speaker
2. Buzzer
3. Relay
4. Motor (Servo, Stepper)
NOTE: Let's discuss your project requirements before placing an order
With over 5 years of experience as an Embedded Software Engineer, I am dedicated to providing top-notch STM32 firmware solutions to ensure the success of your projects. Let's discuss your requirements and make your projects a success.
I have experience in the following areas:
Microcontrollers: STM Cortex m0 m3 m4 m7
Communication Protocols & Drivers: USART/UART, I2C, SPI, CANBUS, I2S
Real Time Operating System (RTOS): FreeRTOS
Data Transmission: MQTT, UDP, TCP
Data Transmission Modules: SIMCOM, QUECTEL, FIBOCOM
Software to be used:
1. ESP32
2. STM32
3. Arduino
4. Raspbery Pi
Languages
1. Embedded C
2. C++
Sensors :
1. Encoder
2. Temperature
3. Humidity
4. Ultrasonic
5. Current
6. Voltage
7. Magnetometer/Gyroscope
8. Accelerometer
9. Barometer
10. Pressure sensor
11. Gas/Smoke
12. Buttons
13. Switches
14. Infra-red (PIR Sensor)
15. Light Dependent Resistor (LDR)
16. Vibration
17. GPS
18. Sound
19. Weight
Displays :
1. GLDC
2. 20x4 LCD
3. 16X2 LCD
4. OLED
5. TFT
Actuators :
1. Speaker
2. Buzzer
3. Relay
4. Motor (Servo, Stepper)
NOTE: Let's discuss your project requirements before placing an order
What the Freelancer needs to start the work
1. What are the specific functionalities and features you require in the firmware?
2. Do you have any preferred microcontroller platforms or hardware specifications for the project?
3. Are there any regulatory or compliance standards that the firmware needs to meet?
We collect cookies to enable the proper functioning and security of our website, and to enhance your experience. By clicking on 'Accept All Cookies', you consent to the use of these cookies. You can change your 'Cookies Settings' at any time. For more information, please read ourCookie Policy
Cookie Settings
Accept All Cookies