I Need Some Technical Graphics Images in PNG
- or -
Post a project like this2138
$$
- Posted:
- Proposals: 4
- Remote
- #2030331
- Awarded
Description
Experience Level: Intermediate
I need a number of graphics provided for a technical project I am working on. They only need to be flat and not 3D and they are based on a modular (fit together policy)
I need 9 images in total. All of the images are based on a simple rectangle with adjustments so please read the next bit carefully.
The 9 images are 3 sets of 3. One set is 20cm x 0.7cm One set is 10cm x 0.7cm and One set is 5cm x 0.7cm All of them should be coloured to represent wood where possible but not too dark
Image one of each set is just a rectangle so one 20 x 0.7cm rectangle, one 10 x 0.7cm rectangle and on of 5cm x 0.7cm very simple indeed.
Image 2 of each set is the same rectangles as above but with 1 x 45 degree angle cut out of one side. So one side will be flat 90 degree rectangle and the other have a 45 degree cut as if a section has been sawn off at 45 degrees. The top (longest edge) though still should measure the full 20, 10 and 5cm.
Image 3 of each set should have 2 45 degree cuts. one at each end. Imagine you were building frame, cutting 45 degree edges at each end, would make 4 pieces of identical wood, fit together as a square (see attached image). So in the image you can see each piece has 2 x 45 degree cuts, so thats what I wan but it doesn't have to be 3D just flat.
If you also look at the image, for the 2nd set, you would only put one of the 45 degree cuts in and leave the other end flat. As previously mentioned, the top of the cut must start at the original size of each rectangle, ie their longest edge should still be 20,10 and 5 respectively.
I need 9 images in total. All of the images are based on a simple rectangle with adjustments so please read the next bit carefully.
The 9 images are 3 sets of 3. One set is 20cm x 0.7cm One set is 10cm x 0.7cm and One set is 5cm x 0.7cm All of them should be coloured to represent wood where possible but not too dark
Image one of each set is just a rectangle so one 20 x 0.7cm rectangle, one 10 x 0.7cm rectangle and on of 5cm x 0.7cm very simple indeed.
Image 2 of each set is the same rectangles as above but with 1 x 45 degree angle cut out of one side. So one side will be flat 90 degree rectangle and the other have a 45 degree cut as if a section has been sawn off at 45 degrees. The top (longest edge) though still should measure the full 20, 10 and 5cm.
Image 3 of each set should have 2 45 degree cuts. one at each end. Imagine you were building frame, cutting 45 degree edges at each end, would make 4 pieces of identical wood, fit together as a square (see attached image). So in the image you can see each piece has 2 x 45 degree cuts, so thats what I wan but it doesn't have to be 3D just flat.
If you also look at the image, for the 2nd set, you would only put one of the 45 degree cuts in and leave the other end flat. As previously mentioned, the top of the cut must start at the original size of each rectangle, ie their longest edge should still be 20,10 and 5 respectively.
Damien S.
100% (2)Projects Completed
1
Freelancers worked with
1
Projects awarded
100%
Last project
5 Jun 2018
United Kingdom
New Proposal
Login to your account and send a proposal now to get this project.
Log inClarification Board Ask a Question
-
There are no clarification messages.
We collect cookies to enable the proper functioning and security of our website, and to enhance your experience. By clicking on 'Accept All Cookies', you consent to the use of these cookies. You can change your 'Cookies Settings' at any time. For more information, please read ourCookie Policy
Cookie Settings
Accept All Cookies