3D cross section of underfloor heating systems
- or -
Post a project like this2182
$$
- Posted:
- Proposals: 7
- Remote
- #1976212
- Awarded
Solidworks, AutoCAD, Ansys, Sourcing and Marketing in China, English Mandarin translation
Shenyang
125633851602671211051683178109219050551921968
Description
Experience Level: Intermediate
We require cross section designs showing the different installation methods of warm water underfloor heating systems. Examples of each type of installation are attached. These are older images that need updating, perhaps with different angles, floor coverings etc. Essentially the images will still be the same, but newer.
Three images required for screed installation
1. in screed with staples
2. in screed with egg crate system
3. in screed with clip rail
Two images required for joist installation:
1. between joist with heat plate
2. between joist with foil insulation
one image required for overlay system
1. overlay system with grooved and foiled board.
Each design must be accurate and the depth of each layer must be to scale as detailed below:
Screed system (top to bottom)
flooring - 30mm
Screed- 65mm
Pipe- 16mm diameter
Foiled insulation- 100mm
Sub Floor- 100mm, but irrelevant as depth does not need to be shown, merely shown as present.
Clip Rail- 25mm
Egg crate- 20mm (from top of node to bottom of base)
Joist system (top to bottom)
Flooring- 25mm
heat plate- 0.5mm
Pipe- 16mm diameter
Gap between heat plate and insulation- 20mm
Foiled insulation- 50mm
Joist baton- 20mm
Grooved and foiled insulation- 50mm
Overlay system:
Flooring- 25mm
Pipe- 16mm diameter
Overlay board- 20mm
Subfloor- merely present
We need these designs no later thanApril 19th.
We have more design examples available if you need them, PPH only allowed 3 to be uploaded to the job proposal.
If you have any question feel free to ask.
Daniel
Three images required for screed installation
1. in screed with staples
2. in screed with egg crate system
3. in screed with clip rail
Two images required for joist installation:
1. between joist with heat plate
2. between joist with foil insulation
one image required for overlay system
1. overlay system with grooved and foiled board.
Each design must be accurate and the depth of each layer must be to scale as detailed below:
Screed system (top to bottom)
flooring - 30mm
Screed- 65mm
Pipe- 16mm diameter
Foiled insulation- 100mm
Sub Floor- 100mm, but irrelevant as depth does not need to be shown, merely shown as present.
Clip Rail- 25mm
Egg crate- 20mm (from top of node to bottom of base)
Joist system (top to bottom)
Flooring- 25mm
heat plate- 0.5mm
Pipe- 16mm diameter
Gap between heat plate and insulation- 20mm
Foiled insulation- 50mm
Joist baton- 20mm
Grooved and foiled insulation- 50mm
Overlay system:
Flooring- 25mm
Pipe- 16mm diameter
Overlay board- 20mm
Subfloor- merely present
We need these designs no later thanApril 19th.
We have more design examples available if you need them, PPH only allowed 3 to be uploaded to the job proposal.
If you have any question feel free to ask.
Daniel
Daniel T.
100% (13)Projects Completed
15
Freelancers worked with
12
Projects awarded
24%
Last project
17 Dec 2019
United Kingdom
New Proposal
Login to your account and send a proposal now to get this project.
Log inClarification Board Ask a Question
-
There are no clarification messages.
We collect cookies to enable the proper functioning and security of our website, and to enhance your experience. By clicking on 'Accept All Cookies', you consent to the use of these cookies. You can change your 'Cookies Settings' at any time. For more information, please read ourCookie Policy
Cookie Settings
Accept All Cookies