Kinetic Intelligence Training System

Units: mm
Sheet size: A1 (preferred) or A2
Scale: 1:10 (A1) / 1:8 (A2)
General tolerances (GA only): ±2 mm unless noted
Datums: D0 = floor plane, D1/D2 = module centerlines per view

⸻

1) SYSTEM LAYOUT (Top View) — GA-001-TV

Purpose

Shows the three free-standing modules and recommended user zone spacing.

Geometry (place in CAD)

Create three blocks/symbols:
• HPM-1(Hand Post Module one)
• HPM-2 (Hand Post Module two)
• FPM (Foot Platform Module)

These coordinates define the recommended starting arrangement only. Add dashed alternate positions.

Footprints (in top view)

HPM base footprint :
• Preferred V1: circular base Ø450
• Draw circle Ø450 at each HPM centre.

FPM base footprint:
• Rectangular base 700×500

⸻

2) HAND POST MODULE (HPM) — FRONT ELEVATION — GA-001-HPM-FE

Purpose

Defines height range, key interfaces, and swivel handle callout.

HPM overall height range
• Min handle pivot height: 305 (1 ft)
• Max handle pivot height: 2135 (7 ft)

Note: This is the handle pivot point height from floor , not the top of the post.

HPM base)
• Base diameter: Ø450 (V1 stability default)
• Full-contact non-slip rubber pad

Telescoping post (first-pass sizes)
• Outer tube: SHS (square hollow section)
• Inner tube: SHS (slides inside)

Height lock (V1 recommended)
• Primary lock: 10 mm ball-lock pin through hole pattern
• Secondary: hand clamp knob (anti-rattle)
• Hole pitch (first pass): 50 mm increments
• Show a typical hole zone spanning 305–2135 mm up the outer tube.

Swivel handle assembly (critical feature)
• One handle per post
• Handle pivot point located on a bracket attached to the inner tube so it moves with height.
• Handle pivot point offset from post centerline: +120 mm (X direction) so knuckles clear the post.
• Bracket vertical position = pivot height range 305–2135.

Free-swivel callout text (must be on GA):

Handle rotates freely 360° No indexed rotation.

Handle dimensions (to show on GA)
• Grip length: 150mm
• Grip diameter: 30–35 (reference only)
• Clearance circle around handle (dashed): 200mm “sweep zone”


3) HAND POST MODULE (HPM) — SIDE ELEVATION — GA-001-HPM-SE

Purpose

Shows forward/back clearance and confirms handle offset.
• Base 450mm shown again
• Post centerline
• Handle offset 120
• Optional: show an additional dashed handle position as a “neutral line”

⸻

4) FOOT PLATFORM MODULE (FPM) — FRONT ELEVATION — GA-001-FPM-FE

Purpose

Defines base, column, height range, and platform size.

FPM platform top height range
• Min platform top height: 305mm
• Max platform top height: 1220mm

FPM base
• Base footprint (from top view): 700×500mm
• Base thickness placeholder: 80mm overall height (ballast inside)
• Underside: non-slip rubber pads or sheet

FPM telescoping column (first-pass sizes)
• Outer tube: 60×60×3 SHS
• Inner tube: 50×50×3 SHS


Height lock (same approach as HPM)
• 10 mm ball-lock pin + clamp knob
• Hole pitch: 50 mm
• Hole zone spanning 300–1150 mm

Foot platform
• Platform plate: 250×200 (W×D)
• Platform corner radius: R10
• Platform thickness: 6mm
• Padding stack: ~20–30 mm total (reference)

⸻

5) FOOT PLATFORM MODULE (FPM) — SIDE ELEVATION — GA-001-FPM-SE

Purpose

Shows platform depth and confirms base depth.
• Base depth: 500
• Platform depth: 200
• Show platform centered on column

⸻

6) KEY NOTES BLOCK (put on GA sheet verbatim)

Functional / safety notes
1. “All modules are free-standing and must resist tipping during asymmetric loading.”
2. “All exposed edges to be deburred; minimum edge radius R1.5.”
3. “Pinch points: design gaps 10 mm in moving zones.”
4. “Height adjustment must have positive engagement and anti-rattle measure.”
5. “Non-slip floor contact required; no metal-to-floor contact.”
6. “Free swivel handle: continuous rotation 360°; no pinned/indexed rotation.”

Prototype notes
7. “All dimensions shown are GA / first-pass for layout and quoting; detail drawings will finalise sections, thicknesses, and hole patterns.”



7) CRITICAL DIMENSIONS SUMMARY (for the drafter’s callout table)
• HPM base: Ø450
• HPM handle pivot height: 305–2135
• HPM spacing: 25mm intervals
• FPM base: 700×500
• FPM platform top height: 305–1220
• FPM platform size: 250×200

⸻

8) WHAT FILES THE CAD PERSON SHOULD OUTPUT (from this brief)

Ask them to deliver:
• GA-001.pdf (A1/A2)
• GA-001.dwg (AutoCAD)
• GA-001.step (optional for 3D reference blocks)
• Simple 2D blocks for HPM and FPM footprints

**PLEASE BEAR IN MIND I AM NOT A DESIGNER AND HAVE DONE MY BEST TO BE ACCURATE**

**Please do confirm details with me if unclear**